Jump to content

Help Van Buren


mbrainerd
 Share

Recommended Posts

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

heyas mbrainerd :)

download and install cablenut 4.08 https://testmy.net/forum/index.php?action=dlattach;topic=1013.0;id=64

download the attached file, unzip it to C:ProgramCablenut

open cablenut adjuster, in top left corner you see file, click load custom settings file, browse to C:ProgramCablenut and dubbleclick on Cable & DSL 2048 1024.ccs

now you have some values set in adjuster, click save to registry and reboot your pc, also reboot your modem and router

make speedtest and post a new tweaktest result

good luck

VanBuren :)

Link to post
Share on other sites

I used that one but speeds dropped down to 1400, uninstalled cable nut set rwin to 20440 last speed test was 1878 down. With my isp probably will not get anymore than that.

Still would like to get more of my upload. Testmy averages around 530, other places dslrepo.cogece.speakeasy I am getting about 750 up.

Will go tech support tomorrow see if I can get them to bump me up another notch to at least get 90% of speed.

Link to post
Share on other sites

Hey Micro. I have been trying to find the website in the forums that you went to to see if your settings were configured right. I remember one of the screenshots said with your rwin settings your download speed are only capable of a certain speed.

Hope you know what I am talking about or maybe someone will.

Link to post
Share on other sites

I used that one but speeds dropped down to 1400, uninstalled cable nut set rwin to 20440 last speed test was 1878 down. With my isp probably will not get anymore than that.

Still would like to get more of my upload. Testmy averages around 530, other places dslrepo.cogece.speakeasy I am getting about 750 up. Will go tech support tomorrow see if I can get them to bump me up another notch to at least get 90% of speed.

Heya mbrainerd :)

you uninstalled it too fast, i havent finetuned anything yet.....

its impossible to make the perfect file that fit all connections without some tuning.

I suggest you re-install cablenut so i can help you

VanBuren :)

btw Cablenut is the only tweakprogram that can boost your upload

Link to post
Share on other sites

:D My upload.

:::.. Upload Stats ..:::

Connection is:: 689 Kbps about 0.7 Mbps (tested with 1013 KB)

Upload Speed is:: 84 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 12 times faster than 56K you can upload 1MB in 12.19 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=CBYKIEOPZ

:::.. Download Stats ..:::

Connection is:: 1514 Kbps about 1.5 Mbps (tested with 2992 KB)

Download Speed is:: 185 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 27 times faster than 56K you can download 1MB in 5.54 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=L1BQ4F7VU

Link to post
Share on other sites

:D

:::.. Upload Stats ..:::

Connection is:: 701 Kbps about 0.7 Mbps (tested with 1013 KB)

Upload Speed is:: 86 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 13 times faster than 56K you can upload 1MB in 11.91 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=OJ40NTAFE

:?

:::.. Download Stats ..:::

Connection is:: 1289 Kbps about 1.3 Mbps (tested with 2992 KB)

Download Speed is:: 157 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 23 times faster than 56K you can download 1MB in 6.52 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=O94KUV012

Upload is looking better download suffering a little Do not know if this will help you but here is a tweak test

http://ttester.broadbandreports.com/tweak/block:2b0e461?service=dsl&speed=2048&os=winXP&via=normal

Link to post
Share on other sites

WEB100 Enabled Statistics:

Checking for Middleboxes . . . . . . . . . . . . . . . . . .  Done

running 10s outbound test (client to server) . . . . . 837.60Kb/s

running 10s inbound test (server to client) . . . . . . 143.80kb/s

------  Client System Details  ------

OS data: Name = Windows XP, Architecture = x86, Version = 5.1

Java data: Vendor = Sun Microsystems Inc., Version = 1.4.2_06

------  Web100 Detailed Analysis  ------

Cable modem/DSL/T1 link found.

Link set to Full Duplex mode

Information: throughput is limited by other network traffic.

Good network cable(s) found

Normal duplex operation found.

Web100 reports the Round trip time = 155.90 msec; the Packet size = 1460 Bytes; and

There were 42 packets retransmitted, 1 duplicate acks received, and 42 SACK blocks received

The connection was idle 0 seconds (0%) of the time

This connection is network limited 99.97% of the time.

  Contact your local network administrator to report a network problem

    Web100 reports TCP negotiated the optional Performance Settings to:

RFC 2018 Selective Acknowledgment: ON

RFC 896 Nagle Algorithm: ON

RFC 3168 Explicit Congestion Notification: OFF

RFC 1323 Time Stamping: OFF

RFC 1323 Window Scaling: ON

Packet size is preserved End-to-End

Server IP addresses are preserved End-to-End

Information: Network Address Translation (NAT) box is modifying the Client's IP address

Server says [66.117.105.128] but Client says [172.25.25.2]

uration: 13200843

c2sData: 2

c2sAck: 2

s2cData: 9

s2cAck: 1

Checking for mismatch condition

(cwndtime > .3) [0.99>.3], (MaxSsthresh > 0) [30660>0],

(PktsRetrans/sec > 2) [3.23>2], (estimate > 2) [0.94>2]

Checking for mismatch on uplink

(speed > 50 [0.15>50], (xmitspeed < 5) [0.83<5]

(rwintime > .9) [0>.9], (loss < .01) [0.00<.01]

Checking for excessive errors condition

(loss/sec > .15) [4.42>.15], (cwndtime > .6) [0.99>.6],

(loss < .01) [0.00<.01], (MaxSsthresh > 0) [30660>0]

Checking for 10 Mbps link

(speed < 9.5) [0.15<9.5], (speed > 3.0) [0.15>3.0]

(xmitspeed < 9.5) [0.83<9.5] (loss < .01) [0.00<.01], (link > 0) [100>0]

Checking for Wireless link

(sendtime = 0) [2.56=0], (speed < 5) [0.15<5]

(Estimate > 50 [0.94>50], (Rwintime > 90) [0>.90]

(RwinTrans/CwndTrans = 1) [0/1=1], (link > 0) [100>0]

Checking for DSL/Cable Modem link

(speed < 2) [0.15<2], (SndLimTransSender = 0) [1=0]

(SendTime = 0) [2.567246261959715E-4=0], (link > 0) [100>0]

Checking for half-duplex condition

(rwintime > .95) [0>.95], (RwinTrans/sec > 30) [0>30],

(SenderTrans/sec > 30) [0.07>30], OR (link <= 10) [100<=10]

Checking for congestion

(cwndtime > .02) [0.99>.02], (mismatch = 0) [0=0]

(MaxSsthresh > 0) [30660>0]

bw = 0.94 based on packet size = 11Kbits, RTT = 155.90msec, and loss = 0.005747126415371895

The theoretical network limit is 0.94 Mbps

The transmit buffer (101.0 KByte) limits the application to 5.06 Mbps

Your receive buffer (256.0 KByte) limits the application to 12.82 Mbps

The network based flow control limits the application to 3.07 Mbps

Client Data reports link is 'T1', Client Acks report link is 'T1'

Server Data reports link is '10 Gig', Server Acks report link is 'Dial-up'

Link to post
Share on other sites

this is what slowing you down

Web100 reports the Round trip time = 155.90 msec; the Packet size = 1460 Bytes; and

There were 42 packets retransmitted, 1 duplicate acks received, and 42 SACK blocks received

The connection was idle 0 seconds (0%) of the time

This connection is network limited 99.97% of the time.

  Contact your local network administrator to report a network problem

all the re transmissions, have you set your NIC duplexmode manually?

If you not using a router and connect directly to modem, run NIC in Autosense

if you using a router force 100 Mbps full duplex

EDIT: here is how you set duplex mode, ignore the suggestion of half duplex, use Autosense instead quote from http://dslnuts.com/tips_tricks.shtml

"Windows 2000 or XP: to change to half-duplex:

* Open Control Panel.

* Double-click Network and Dial-up Connections.

* Identify the icon for your cable modem connection: usually Local Area Connection.

* Right-click that icon and select Properties.

* Under the ethernet adapter icon, click the button Configure.

* Click the tab Advanced to bring it to the front:

* In the Property box, the property name to be selected varies according to model of ethernet card. Examples are: Network Link Selection, Media Type, Connection Type, Duplex Mode, or any similarly-named property which can have Values looking like Auto-Negotiation, or 10BT, or 10BaseT.

* In the Value box, select a value which either (a) explicitly says half-duplex or semi-duplex, or (B) at least does not say full-duplex [e.g. 10BaseT on its own is OK]. If there is a choice between 10 and 100 with half-duplex, choose the 10. Do not choose 10Base5, 10Base2, or AUI.

* Click OK to exit the Adapter settings.

* Click OK to exit the Connection properties. "

VanBuren :)

Link to post
Share on other sites

this is what slowing you down

Web100 reports the Round trip time = 155.90 msec; the Packet size = 1460 Bytes; and

There were 42 packets retransmitted, 1 duplicate acks received, and 42 SACK blocks received

The connection was idle 0 seconds (0%) of the time

This connection is network limited 99.97% of the time.

  Contact your local network administrator to report a network problem

all the re transmissions, have you set your NIC duplexmode manually?

If you not using a router and connect directly to modem, run NIC in Autosense

if you using a router force 100 Mbps full duplex

VanBuren :)

I have the Lingo router for voip! How do I change the setting?

I lowered my rwin to 20440 and got this result

:::.. Download Stats ..:::

Connection is:: 1649 Kbps about 1.6 Mbps (tested with 2992 KB)

Download Speed is:: 201 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 29 times faster than 56K you can download 1MB in 5.09 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=C2GF7TZX8

Link to post
Share on other sites

:::.. Download Stats ..:::

Connection is:: 1718 Kbps about 1.7 Mbps (tested with 2992 KB)

Download Speed is:: 210 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 31 times faster than 56K you can download 1MB in 4.88 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=85T017BCV

:::.. Upload Stats ..:::

Connection is:: 734 Kbps about 0.7 Mbps (tested with 2992 KB)

Upload Speed is:: 90 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 13 times faster than 56K you can upload 1MB in 11.38 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=BMTOPWC8V

How do I manual;ly do the nic? : :oops:

Link to post
Share on other sites

here is how you set duplex mode, ignore the suggestion of half duplex, use Autosense instead quote from http://dslnuts.com/tips_tricks.shtml

"Windows 2000 or XP: to change to half-duplex:

* Open Control Panel.

* Double-click Network and Dial-up Connections.

* Identify the icon for your cable modem connection: usually Local Area Connection.

* Right-click that icon and select Properties.

* Under the ethernet adapter icon, click the button Configure.

* Click the tab Advanced to bring it to the front:

* In the Property box, the property name to be selected varies according to model of ethernet card. Examples are: Network Link Selection, Media Type, Connection Type, Duplex Mode, or any similarly-named property which can have Values looking like Auto-Negotiation, or 10BT, or 10BaseT.

* In the Value box, select a value which either (a) explicitly says half-duplex or semi-duplex, or (B) at least does not say full-duplex [e.g. 10BaseT on its own is OK]. If there is a choice between 10 and 100 with half-duplex, choose the 10. Do not choose 10Base5, 10Base2, or AUI.

* Click OK to exit the Adapter settings.

* Click OK to exit the Connection properties. "

Link to post
Share on other sites

:)

:::.. Download Stats ..:::

Connection is:: 1676 Kbps about 1.7 Mbps (tested with 2992 KB)

Download Speed is:: 205 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 30 times faster than 56K you can download 1MB in 5 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=VA7EM1NH9

:::.. Upload Stats ..:::

Connection is:: 706 Kbps about 0.7 Mbps (tested with 1013 KB)

Upload Speed is:: 86 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 13 times faster than 56K you can upload 1MB in 11.91 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=M3J1T7WGA

I was on my Lingo phone during tests. I gues that might suck up some of my speed. I also have a call into my isp, to see if they actually bumbed me to the 2048/1024 and not the 1.5/768.

Getting better! :D

Link to post
Share on other sites

:::.. Download Stats ..:::

Connection is:: 1720 Kbps about 1.7 Mbps (tested with 2992 KB)

Download Speed is:: 210 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 31 times faster than 56K you can download 1MB in 4.88 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=G6PDU8BJW

:::.. Upload Stats ..:::

Connection is:: 695 Kbps about 0.7 Mbps (tested with 1496 KB)

Upload Speed is:: 85 KB/s

Tested From:: http://www.testmy.net/

Bottom Line:: 12 times faster than 56K you can upload 1MB in 12.05 second(s)

Validation Link:: https://testmy.net/cgi-bin/get.cgi?Test_ID=EBJQ4Z1WO

TCP/Web100 Network Diagnostic Tool v5.2.1e

click START to begin

Checking for Middleboxes . . . . . . . . . . . . . . . . . .  Done

running 10s outbound test (client to server) . . . . . 528.35Kb/s

running 10s inbound test (server to client) . . . . . . 1.12Mb/s

Your PC is connected to a Cable/DSL modem

Link set to Full Duplex mode

No network congestion discovered.

Good network cable(s) found

Normal duplex operation found.

Web100 reports the Round trip time = 132.77 msec; the Packet size = 1460 Bytes; and

There were 1 packets retransmitted, 12 duplicate acks received, and 13 SACK blocks received

The connection was idle 0 seconds (0%) of the time

This connection is receiver limited 69.03% of the time.

  Increasing the current receive buffer (19.0 KB) will improve performance

This connection is network limited 30.92% of the time.

  Contact your local network administrator to report a network problem

    Web100 reports TCP negotiated the optional Performance Settings to:

RFC 2018 Selective Acknowledgment: ON

RFC 896 Nagle Algorithm: ON

RFC 3168 Explicit Congestion Notification: OFF

RFC 1323 Time Stamping: OFF

RFC 1323 Window Scaling: OFF

Packet size is preserved End-to-End

Server IP addresses are preserved End-to-End

Information: Network Address Translation (NAT) box is modifying the Client's IP address

Server says [66.117.105.128] but Client says [172.25.25.2]

(SenderTrans/sec > 30) [0.10>30], OR (link <= 10) [100<=10]

Checking for congestion

(cwndtime > .02) [0.30>.02], (mismatch = 0) [0=0]

(MaxSsthresh > 0) [10220>0]

bw = 2.60 based on packet size = 11Kbits, RTT = 132.77msec, and loss = 0.001038421643897891

The theoretical network limit is 2.60 Mbps

The transmit buffer (101.0 KByte) limits the application to 5.94 Mbps

Your receive buffer (19.0 KByte) limits the application to 1.17 Mbps

The network based flow control limits the application to 1.25 Mbps

Client Data reports link is 'T1', Client Acks report link is 'T1'

Server Data reports link is '10 Gig', Server Acks report link is 'T1'

Hope you understand all of this.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share


×
×
  • Create New...