Jump to content

New way to access ur CANOPY Web Page (SMART BRO-ken)


tamie77

Recommended Posts

  • Replies 383
  • Created
  • Last Reply

Top Posters In This Topic

first do these steps

1.) go to network connections in the control panel

2.) right click on the local area network

3.) highlight Internet Protocol and click on properties

4.) set to Use the Following IP address

5.) set the IP Address to "10.20.30.40"

6.) set the Subnet to "255.0.0.0"

7.) leave the gateway blank

8.) leave the DNS blank

9.) apply the changes

Link to comment
Share on other sites

this is what ive read...

However, may mga cases for some modules na pinalitan ng 10.xx.xx.xx ang IP address.  So, kung hindi gumagana yung IP address sa number 1.  Try niyo gamitin yung 10.xx.xx.xx.  Ano yung xx's?  Only when the canopy lite SM is within your reach can you use this 10.xx.xx.xx scheme dahil dependent sa nakasulat na number sa loob ng module yung mga xx.  Just get the last 6 characters of the number that you are going to get inside the module (pag tinanggal niyo yung cover ng RJ-14/11 slots) and convert each 2 characters to decimal (base 16 to base 10).  Kung di kayo marunong magconvert, check niyo sa net, marami dung pangconvert.  Basta ang main idea, pag-base16, nagbibilang ka from 0 to F, so after 9, imbis na 10, A then B, C, D, E, F, tapos saka palang 10.  Meaning, ang 10(base 16) ay 16(base 10).  Mas madaling magconvert from hex to binary, tapos binary to decimal.  Halimbawa... 10(base 16) ay 10000(base 2) tapos 2^4(base 10) = 16 (two raised to the fourth power).  Fourth power dahil nagcocorrespond yung rightmost zero to a power of 0.

Link to comment
Share on other sites

oh got it... when i tried it back in my cmd.exe and typed arp -a, there is no 3rd line or digits that shows the ip unlike in this example

PART 2: The Canopy IP Address Quest

Now you need to know your Canopy IP Address. There are two ways I know of:

-> Method 1 (The Safe Way):

1. Go to Start -> Run -> cmd.exe. On the command promt,

type arp -a (take note of the space after the word arp).

The command prompt will display several IP addresses. Example:

C:Documents and Settingsgiluk_no_jutsu>arp -a

Interface: 10.20.30.40 --- 0x2

Internet Address Physical Address Type

10.0.0.1 0a-00-3e-f7-de-2d dynamic

10.247.222.45 0a-00-3e-f7-de-2d dynamic

what happened? did i miss sumthing?

Link to comment
Share on other sites

@gerger21

i think you have to change the last digit of the ip that you got.

for example, if you got 10.222.333.444,you should change it to 10.222.333.441

try that and post results. alsoo,read the how to tweak smartbro thread, and give close attention to posts by jun101. he has good advise about using the esn# .

Link to comment
Share on other sites

@gerger21

i think you have to change the last digit of the ip that you got.

for example, if you got 10.222.333.444,you should change it to 10.222.333.441

try that and post results. alsoo,read the how to tweak smartbro thread, and give close attention to posts by jun101. he has good advise about using the esn# .

correct!

Link to comment
Share on other sites

guys if there are many 10.xx.xx.xx appear at ur cmd promt (arp -a)

try to search for ur account ther u can see the service reference no.

and the name of the subscriber of the smart bro, if anyone ther cant access

ther canopy i have disovered another way hehehehehe  :haha:

but seems you guys can access maybe its no longer important to post it

well try first the procedure of elijahpaul hirs the link

http://www.testmy.net/t-18616.0

and if its not working try my procedure

http://www.testmy.net/t-20597.0

and if u cant access ur canoy post it hir so that ill post what i have discovered

:evil6: :evil6: :evil6: :evil6: :evil6: :evil6: :evil6: :evil6: :evil6: :evil6: :evil6:

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.

×
×
  • Create New...